Amerec 9128-131
KT3 Digital Steam Shower Generator Control w/Built-in Sensor, AK Series
The Amerec 9128-131 (KT3) control works with Amerec AK series steam generators and is intended as a replacement or additional control only. A stylish update to Amerec's KT60 control, the Amerec 9128-131 control is backward compatible with the classic KT60. Featuring a built-in temperature sensor, this steam shower generator control was designed for use inside the steam room. With the simple ease of 3-buttons, you control on/off, temperature, and time duration settings. The display alternates every 5 seconds between atmospheric room temperature and the remaining time of your steam session. With maximum session settings of up to 125 °F and 60 minutes (residential use), this control compliments any AK series generator.
Control Only (cable and steam head not included)
NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable
The Amerec 9128-131 (KT3) control works with Amerec AK series steam generators and is intended as a replacement or additional control only. A stylish update to Amerec's KT60 control, the Amerec 9128-131 control is backward compatible with the classic KT60.
Featuring a built-in temperature sensor, the Amerec 9128-131 (KT3) steam shower generator control was designed for use inside the steam room. With the simple ease of 3-buttons, you control on/off, temperature, and time duration settings. The display alternates every 5 seconds between atmospheric room temperature and the remaining time of your steam session. With maximum session settings of up to 125 °F and 60 minutes (residential use), this control compliments any AK series generator.
For a temperature controlled steam bath, the AK generator requires either a KT3 with a built-in temperature sensor or a K3 with a separate temperature sensor. Another K3 may be added to allow two controls for a steam bath, such as one inside the room and one outside, but if a KT3 is installed it must be inside the steam room. A maximum of two controls may be installed.
The temperature can be adjusted from 84 to 125 °F (29 to 52°C) with an initial default of 120 °F (49°C). The temperature display preference may be set using a jumper on the steamer circuit board to select either °F (default) or °C. The maximum bath time may be set to 60 minutes (default) or 24 hours (for light commercial use) using a jumper on the steamer circuit board.
This control must be mounted inside the steam room, approximately 4 feet up from the floor, as it contains the temperature sensor. A K3 control may be installed outside the steam room as a second control. Either control may be used to control the steam bath.
The low voltage controls can be mounted up to 25ft from the steam generator. This control must be mounted inside the steam room so its built-in temperature sensor will function. String the 25ft cable from the control location through 1/2” holes in the wall studs or ceiling joists to the generator.
Control Only (cable and steam head not included) Please see the Amerec KT3 if the full control kit is needed.
- Black control display panel
- Settable on/off, time, temperature, and delay
- Settable temperature range of 84-125 °F
- Inside steam room installation
- Displays and room temperature
- Built-in temperature sensor
- Designed, engineered, and made in the USA
- Control Console Dimensions: 3"W x 0.5"D x 3"H
- Limited Lifetime Warranty
- 9128-131 (KT3) Control
- Installation and Operation Manual
- Limited Lifetime Warranty
| Model | 9128-131 |
|---|---|
| Minimum Temperature Setting | 84°F |
| Maximum Temperature Setting | 125 °F |
| Minimum Session Timing | 5 minutes |
| Maximum Session Timing | 60 minutes(Residential) 24 Hour(Light Commercial with jumper use) |
| Installation | Wall-mount Inside Steam Room |
| Width | 3" |
| Depth | 0.5" |
| Height | 3" |
The Amerec KT3 steam shower generator control kit works with Amerec AK series steam generators. A stylish update to Amerec's KT60 control, the control is backward compatible with the classic KT60. Featuring a built-in temperature sensor, this control was designed for use inside the steam room. With the simple ease of 3-buttons, you control on/off, temperature, and time duration settings. The display alternates every 5 seconds between atmospheric room temperature and the remaining time of your steam session. With maximum session settings of up to 125 °F and 60 minutes (residential use), this control kit includes a ComfortFlo steam head.
6 different Steam head finishes for the KT3 control kit are available.